VeEX VePAL TX300M Скачать руководство пользователя страница 141

Страница: 141 / 421

The OTU framing is divided into two portions: FAS and MFAS.

Frame Alignment Signal (FAS)

Uses the first six bytes and, similar to SONET/SDH, it is used to provide framing for the entire signal

In order to provide enough 1/0 transitions for synchronization, scrambling is used over the entire OTU frame, except

for the FAS bytes

MultiFrame Alignment Signal (MFAS)

Byte is used to extend command and management functions over several frames

The MFAS counts from 0 to 255, providing a 256 multiframe structure

Go back to top

Go back to TOC

9.2.2 Optical Transport Unit (OTU) Analysis

The OTU overhead is comprised of the SM, GCC0, and RES bytes.

Section Monitoring (SM)

Bytes are used for the Trail Trace Identifier (TTI), Parity (BIP-8) and the Backward Error Indicator (BEI) (also known

as the Backward Incoming Alignment Error [BIAE]), Backward Defect Indicator (BDI), and Incoming Alignment Error

(IAE).

The TTI is distributed over the multiframe and is 64 bytes in length. It is repeated four times over the multiframe.

SM TTI Type

General Communication Channel 0 (GCC0)

Clear channel used for transmission of information between OTU termination points

GCCO Type

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды