VeEX VePAL TX300M Скачать руководство пользователя страница 276

Страница: 276 / 421

Control

The

Control

button becomes available on the right side menu when any Ethernet application (V-SAM, RFC 2544, Throughput, BERT)

is selected. Press the

Control

button to configure loop up and loop down commands necessary to control a far-end unit. The loop up

command contains information about the test layer. Looping back test traffic is possible as follows:

Layer 1:

All incoming traffic is looped back unchanged

Layer 2:

All incoming unicast traffic is looped back with the MAC source and destination addresses swapped

Layers 3 & 4:

All incoming unicast traffic is looped back with MAC/IP source and destination addresses swapped

To configure loopback control on the unit, select from the following options under

Partner Address

MX Discovered:

Lists MX discovered devices. Select from the list of discovered devices to loop up/down

User Defined:

Input the destination IP address of the far-end device

OAM Discover

: Lists OAM discovered devices. Select from the list of discovered devices to loop up/down

Remote Partner Control

The

Peer-to-Peer

option is available only for RFC 2544 testing. For more information on

Peer-to-Peer

mode, please see

15.3.1.4

Peer-to-Peer and Asymmetric Testing

Go back to top

Go back to TOC

OAM Discover

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды