VeEX VePAL TX300M Скачать руководство пользователя страница 307

Страница: 307 / 421

15.3.1.4 Peer-to-Peer and Asymmetric Testing

Remote Partner Control

When the local unit connects to the remote (peer) partner, it loads the same configuration profile (header, traffic, and frame size)

to the remote partner, with the MAC and IP addresses inverted. From the peer-to-peer menu, asymmetric testing becomes

available.

Asymmetrical links provide different line rates in the two directions. To verify the information for both the low and the high rates

of the link, the user needs to send a test signal from one instrument located at one end of the link to an instrument at the other

end of the link and vice versa to test traffic capacity. The two test instruments have to be synchronized because the tests defined

in RFC 2544 require the receiver to know the contents of the test signal to be transmitted in detail.

The TX300/e offers an automated RFC 2544 test application to perform throughput, frame loss, and burstability tests in a local-

remote unit setup. The user first configures the test setup in the local unit. Once initiated, the local unit transfers the setup

information to the remote unit via the line under test. Upon completion, the remote unit transfers the test results back to the local

unit, enabling the user to read the results for both directions of the link on the local unit.

Asymmetric Control

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды