VeEX VePAL TX300M Скачать руководство пользователя страница 339

Страница: 339 / 421

15.5.1.5 Error Injection Settings (Per Stream Configuration)

Error injection can be performed during test. The type of errors and error injection are configured in the Error Injection tab. Once

the test is running, error injection can be performed by pressing the

Error Inject

button on the right side of the screen.

Stream #:

Select the stream to configure.

Error type:

Select from CRC, IP Checksum (Layer 3, 4 only), TCP/UDP Checksum (Layer 4 only), or Pause. With Pause

selected, the unit will transmit a pause frame when the

Error Injection

icon is pressed. The Pause time duration is

configurable in units of 512 bit time. At Gigabit Ethernet speed, this is equivalent to 512 ns. For example, if pause time is

set to 1000, the pause duration will be set to 1000x512 ns.

Injection Flow:

The error injection flow determines how the selected errors will be injected. The user can select a single

error or a specific count.

Count:

The user will be able to configure the error count via numeric keypad.

Throughput Test - Error Injection Settings per Stream

Go back to top

Go back to TOC

15.5.1.6 Alarm Injection Settings

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды