VeEX VePAL TX300M Скачать руководство пользователя страница 358

Страница: 358 / 421

Service Level OAM Configuration Parameters

MD Name:

Name of the Maintenance Domain (only for 802.1ag)

MA Name:

Enter the name of the 802.1ag MA or Y.1731 MG

MD Level:

Maintenance domain level (0 to 7)

MEP ID:

End point identifier (1 to 8191)

Primary VLAN ID:

VLAN ID associated with the MA or MEG

Direction

Up:

Inward facing MEP used for MA/MEG with a wider reach (i.e., end-to-end, beyond a single link)

Down:

Outward facing MEP used for MA/MEG spanning a single link

Destination MEP ID:

MEP ID of the MEP end point

Differences between 802.1ag and Y.1731

Selecting

802.1ag

enables Continuity Check Messages (CCM), Loopback Message (LBM) and Link

Trace Message (LTM).

ITU-T Y.1731

provides all of the 802.1ag functionality with additional

performance monitoring capabilities including Frame Loss (LM), and Delay (DM).

IEEE 802.1ag Definitions

Maintenance Domain (MD) :

Management space on a network that is owned and operated by a single network provider. There

is a maintenance level (from 0 to 7) to define the hierarchical relationship between domains. Maintenance domains can be

nested but never intersect. MD is defined by Operational or Contractual Boundaries (e.g., Customer/Service Provider/Operator).

Maintenance Association (MA):

Association of Maintenance. Elements that comprise the Maintenance domain.

Maintenance Elements can either be MEPs (End points) or MIPs (Intermediate Points)

MEPs are at the edge of the network. They can generate and respond to OAM messages. A point-to-point EVC has only

2 MEPs, a multi-point EVC has multiple MEPs.

MIPs are located between the MEPs and can be used to isolate network problems. MIPs cannot generate OAM

messages but can respond.

Maintenance Level:

Identifies the network hierarchy. Higher Level = Largest network. Level information present in all OAM

PDU frames.

Level 0,1,2 = Operator domain

Level 3,4 = Service Provider domain

Level 5,6,7 = Customer domain

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды