VeEX VePAL TX300M Скачать руководство пользователя страница 394

Страница: 394 / 421

Valid settings are 1% to 100% in 0.01% increments

Traffic Setup

Error Injection Setup

Error injection can be performed during a test. The type of errors and error injection rate or flow are configured in the Error Injection

tab.

Error type:

Select from Bit and CRC.

Injection Flow:

Determines how the selected errors will be injected. The user can select a single error injection, a specific

count, or error rate.

Rate and Count:

The user is able to configure the error rate (when rate is selected) and error count via the numeric pop-up

keypad.

Error Injection Setup

Once the test is running, error injection can be enabled by selecting the

Error Injection

icon from the action drop-down menu at the

top of the screen. Press the

Error Inject

button to start injecting errors.

Go back to top

Go back to TOC

16.2.4 Starting Measurements

Start

button: Click to start the measurement.

Laser

button: Can be turned On or Off to make adjustments to the fiber patch cord, etc.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды