VeEX VePAL TX300M Скачать руководство пользователя страница 381

Страница: 381 / 421

Confusing naming and spelling conventions have stuck with Fibre Channel during its development.

The word “channel” in no way indicates a preference for channel protocols or environments.

Even though “fibre” and “fiber” are semantically equivalent (“fibre” is the international English

spelling), “Fibre Channel” is the official spelling for the technology.

“Fiber” has come to mean more specifically the optical (glass) media used for long-distance (up to

10 km) connections.

Go back to top

Go back to TOC

16.1.2 Test Applications

The Fiber Channel test mode is accessed by clicking the Test Mode button at the bottom right hand side of the screen.

The Fiber Channel Home screen or Main Menu is shown below.

Fiber Channel Main Menu

The Fiber Channel Main Menu provides shortcut application buttons for FC BERT, FC RFC 2544, FC Throughput, FC Loopback, and

IP testing.

Some test capabilities or test rates may be specific to the product configuration or may require the purchase of a software option in

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды