VeEX VePAL TX300M Скачать руководство пользователя страница 360

Страница: 360 / 421

Loss Measurement (LMM/LMR) (Y.1731 Only)

Delay Measurement (DMM/DMR) (Y.1731 Only)

General Setup

To run any 802.1ag/Y.1731 Tests, fill out the listed parameters and press

Start

. In the case of

CCM

, select

Enable

from the drop-

down menu to run that test. Details on individual test parameters will be listed in the specified section.

802.1ag/Y.1731 Connectivity Fault Management Functions

supported by the TX300/e are as listed:

Fault Detection – Continuity Check:

CCM "heartbeat" messages are transmitted at a configurable periodic interval by MEPs.

Network/Path Discovery – Link trace message:

Equivalent to a traceroute test. MIPs and MEPs along the path send a response.

Fault verification and isolation – Loopback:

Verify connectivity to a specific point in the message. Equivalent to ping test.

Continuity Check Messages (CCM)

CCM Messages are multicast messages sent from MEP to MEP at configurable intervals. Loss of continuity is detected after no CCM

is received for 3.5 times the CCM interval.

Note

: There can be 4,094 VLANs per port and up to eight maintenance levels. This yields a worst case CCM transmission rate of 9.8

million CCMs per second if 3.3ms interval is used.

Continuity Check Message (CCM)

RDI Flags added in CCM Messages indicates loss of continuity in the remote direction.

CCM Message Format

Service Level OAM (Page 1)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды