VeEX VePAL TX300M Скачать руководство пользователя страница 357

Страница: 357 / 421

Notice that each device can be placed in any mode as long as the remote and local device are not both in passive mode.

Discovery Capabilities:

Capabilities advertised during discovery process

Remote Loopback

Link Events: Supported, but no stateful

MIB Retrieval: Can be advertised but is not supported in current release

Unidirection

Remote Loopback:

The user can transmit a loopback command to place the remote unit into loopback mode. Every frame received

is transmitted back on the same port to ensure the quality of links during installation or troubleshooting and for fault isolation testing.

Link Events:

Event OAMPDU is transmitted when the link error exceeds the threshold. Events may be sent once or multiple times. In

the current software release, link events are only transmitted upon user request, not based on threshold crossing.

MIB Retrieval:

Retrieves information on network devices and interfaces.

Unidirection:

Checks for unidirectional transmission.

Go back to top

Go back to TOC

15.6.1.2 Service Level OAM: 802.1ag/Y.1731 Setup

Under the

Service Level OAM

tab, the user has the option of starting the 802.1ag or Y.1731 test.

Fill out the given parameters.

MD Name

MA Name

VLAN

, and

MD Level

input values must match for both connected OAM

devices in order for the test to work. The

Destination MEPID

and

Local MEP ID

must also be inverted for the tests to work.

Tap the box next to 802.1ag or Y.1731 to start the selected test. The transmission of OAM PDUs become active as soon as the

checkmark is added to the test.

OAM - Service Level OAM (Page 1)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды