VeEX VePAL TX300M Скачать руководство пользователя страница 292

Страница: 292 / 421

15.2.1.2 Traffic Settings

Traffic tab:

The user configures the traffic profile for the stream, including traffic flow, frame size, frame type, and transmit rate.

Traffic Flow:

Select from the following traffic flows:

Constant:

The selected frame is transmitted continuously according to the selected bandwidth %.

Ramp:

The selected frame is transmitted at maximum bandwidth according to the selected duty cycle and burst

period.

Burst:

The selected frame is transmitted in a staircase profile according to user selectable step time, number of

steps, and maximum bandwidth.

Single Burst:

Configure the number of frames to be transmitted in the burst along with the bandwidth. For

example, if 100000 frames are transmitted at 12.5% of bandwidth, on a 1Gbps line, 100000 frames will transmit at a

rate of 125Mbps and then the burst will stop.

Frame Size Type:

Fixed or Uniform min and max frame length values. Uniform traffic is traffic generated with a uniform

distribution of frame lengths.

Frame Size (bytes):

Enter the frame size when a Layer 2, 3, or 4 BERT is selected

Frame size configuration is not available for Layer 1 BERT

Frame sizes can be from 64 bytes to 1518 bytes, in addition to jumbo frames up to 10000 bytes

BW (Transmit Bandwidth):

Configure the transmit rate for the test

When traffic flow is equal to Burst, two burst bandwidths are configured with burst time

When traffic flow is equal to Ramp, starting and an ending bandwidth are configured along with the bandwidth step

size and duration

BERT Setup - Constant Traffic

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды