VeEX VePAL TX300M Скачать руководство пользователя страница 228

Страница: 228 / 421

Please see

11.7.1.7 Multi Call

for more information.

Trace

: Please see

Trace: ISDN Protocol Decode

under

11.7.1.3 Call - Voice and 3.1K Audio Setup

Result

: Press the green arrow to access the action menu and press Start to initiate BERT Testing. Please refer to

11.7.1.5

Data Call BERT Results

for more details.

Go back to top

Go back to TOC

11.8 E1 VF

Tapping the VF in the PDH Tools screen displays the VF Tasks. The VF menu performs a variety of talk/listen functions.

VF Tasks

VF Testing

Do not attempt to enter VF Tasks if the Frame LED is not green.

Green LEDs indicate that the framing found on the received signal matches the framing selected in

the Setup screen.

It is impossible to talk, listen, or perform other channelized functions in the absence of frame

synchronization, since channels can be identified only within a framed signal.

Setup:

Time Slot:

Channel to test for both transmitting and receiving. Input a number from 1 - 31.

Mode:

Talk or send a tone on the transmit signal. It is possible to transmit audio data from the external headset into

selected timeslot.

Code:

u-Law or A-Law.

Transmitted Frequency:

50 to 3950Hz.

Transmitted Level:

-60 to 3dBm.

Programmable ABCD:

Change the signalling bits transmitted with the associated transmit channel. These bits will be

transmitted only if the test set is using MFAS (PCM-30) framing. Pressing IDLE(1001), SEIZE(0001), User (manually set)

will place that signal onto the A/B/C/D position. D: Manual edit ABCD (User) or IDLE, SEIZE.

Results:

Measure signal frequency and level in selected timeslot

Listen to the voice channel in selected timeslot via external headset

ABCD: View the received Channel Associated Signalling System (CAS) bits

Data: View the live 8-bit channel data as it is received from the selected channel

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды