VeEX VePAL TX300M Скачать руководство пользователя страница 211

Страница: 211 / 421

11.0 PDH Tools

Accessing PDH Tools

On the TX300, tap on Home (main menu) >

Advanced Mode

PDH Tools

On the TX300e, tap on Home (main menu) >

PDH Tools

PDH Menu

Go back to top

Go back to TOC

11.1 E1 Pulse Mask

This function captures and analyzes E1 (2.048Mbps) pulse shape. The purpose of maintaining the correct pulse shape is to

reduce inter-symbol interference – if the logic 1s and 0s cannot be detected by the receiver correctly, bit and code errors will

result.

The pulse amplitude and overall shape are superimposed and compared with the ITU-T G.703 pulse conformance template.

Telecommunications signals require specific load impedance for pulse mask compliance testing to be accurate. When high

frequency pulses are transmitted down a transmission line, a portion of the pulse will be reflected when and wherever it

encounters an impedance mismatch. The reflection is proportional to the impedance mismatch (i.e., the greater the mismatch, the

greater the reflection of the pulse). To avoid reflections impacting the E1 measurement, the TX300/e will terminate twisted pair

cables with 120 ohms and coax cable with 75 ohms impedance. Note that 75 Ohm and 120 Ohm twisted pair cables each have

different nominal amplitudes associated with them; for the 75 Ohm coax cable, the pulse amplitude must be 2.37V ± 10% while

for 120 Ohm twisted pair cables, the pulse amplitude must be 3.0V ± 10%.

According to the G.703 recommendation, E1 pulses need only be measured at the transmitter output, and are

not

required to

meet the pulse template over a variety of cable lengths. This of course will not provide information on distortions caused by

misalignment and other impairments of the line. The TX300/e on the other hand can connect to a live system at the TX output

port via a Protected Monitoring Point (PMP) or at the far-end of a transmission line. In either case, the signal will be attenuated or

amplified as necessary to compensate for test point or cable attenuation characteristics.

E1 Pulse Mask

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды