VeEX VePAL TX300M Скачать руководство пользователя страница 338

Страница: 338 / 421

Multiple Streams - MAC/IP Address Setup

If all of the streams are going to the same far-end unit, then the MAC/IP destination addresses

must be the same on all of the streams.

If any of the traffic streams are going to more than one far-end unit then ensure the correct MAC/IP

destination addresses are configured for the respective streams.

Go back to top

Go back to TOC

15.5.1.4 Traffic Settings (Per Stream Configuration)

In the Traffic tab the user is able to configure the traffic profile per stream, including frame size selection, traffic type, and

transmit rate.

Stream #:

Select a stream number to configure.

Traffic Flow:

Select from Constant, Ramp, Burst, or Single Burst traffic flow.

Frame Size (Type):

Fixed or Uniform. If uniform is chosen, the user will have to input a minimum and maximum frame

size.

Frame Size (bytes):

If a fixed frame size is chosen, this option is enabled. Enter the frame size when a Layer 2 or 3 is

selected. Frame sizes can be from 64bytes to 1518bytes, in addition to jumbo frames up to 10k bytes.

BW (Transmit Bandwidth):

Configure the transmit rate for the stream.

Note:

The bandwidth allocation per stream is already configured in the

General Settings

tab, but can be modified in this

screen as well.

For more information on Traffic Settings, please see

15.2.1.2 BERT Traffic Settings

Throughput Setup - Traffic Setup - Constant Traffic Flow

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды