VeEX VePAL TX300M Скачать руководство пользователя страница 320

Страница: 320 / 421

RFC 2544 Results - Burstability (Test Log)

Go back to top

Go back to TOC

15.3.3 Saving RFC 2544 Results

Once the test has been stopped the results can be saved by pressing the

Save

key on the VePAL’s keypad. The results will be

saved and named automatically. Once the results are saved, the user may view or rename the results file by going to

Home

Files

Saved

. Please see

10.2 Recalling or Viewing Files and Test Results

in the

V300 Common Functions manual

for

more information.

Go back to top

Go back to TOC

15.3.4 Advanced SLA Mode

Using this test function, users are able to verify SLAs while end-to-end QoS is assessed properly. By configuring one primary test

stream and up to seven background streams each with independent frame size, bandwidth, and more importantly QoS levels,

simulating different service applications is now realized. The Advanced RFC 2544 SLA mode provides detailed visibility of the test

parameters for each of the traffic streams being measured, providing an efficient in-depth qualification in a fast and automated

way.

Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды