VeEX VePAL TX300M Скачать руководство пользователя страница 107

Страница: 107 / 421

7.3.2 Errors/Alarms

The Errors/Alarms tab brings up several pages showing error and alarm statuses.

Page 1 provides an overview of all the Errors and Alarms applicable to the signal or network under test. The color of the page

tab is normally blue; however, it will turn red when an alarm error condition has been detected or recorded.

The soft LEDs on screen are arranged logically and will depend on signal hierarchy, structure, payload, and framing selected.

The soft LEDs have a tricolor function:

Green:

No error or alarm is present.

Red:

An error or alarm condition is detected and is currently present.

Yellow:

Indicates a history condition. An error or alarm was detected during the measurement interval but it is no longer

present or active.

Errors/Alarms (Page 1)

Note:

Tapping the individual soft LED will automatically link you to the applicable result screen which provides detailed

information.

The LED headers are described in the table below:

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды