VeEX VePAL TX300M Скачать руководство пользователя страница 75

Страница: 75 / 421

Auto-config tab

The

Auto-Config

function automatically sets the receiver of the test set. A search for SDH and PDH signals at both the electrical

or optical inputs is performed to determine the signal structure. For electrical signals, both Terminated and PMP voltage ranges

are searched and supported.

Procedure

Tap on the

Start

button

to begin the search. The received signal is checked for network type, hierarchy and bit

rate, payload structure, payload framing, test pattern and signal level. If the search is successful, a “PASS” result is displayed.

Search parameters and criteria

Interface:

Checks physical parameters (bit rate line code).

Mapping:

Checks mapping structure using the signal label and pointer bytes.

Payload:

Only test patterns defined in ITU-T or ANSI standards will be recognized. If no test pattern is detected, the unit

assumes live traffic.

PDH Signals:

Unframed or framed payloads at all hierarchies. For 1.5M signals containing 64kbps timeslots, the TX300/e will

assume live traffic and will not search for a test pattern.

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды