VeEX VePAL TX300M Скачать руководство пользователя страница 342

Страница: 342 / 421

Go back to top

Go back to TOC

15.5.1.8 Starting/Stopping a Throughput (Multiple Streams) Test

Once all configurations have been made, the user can start the Throughput test (press the

Start

icon on the top right section of

the screen). The following are three scenarios of how to prepare and start the unit for Throughput testing.

Note:

If testing on the fiber ports, make sure the LASER is turned On before starting the test.

End-to-End Testing

Connect the TX300/e to another MX or TX unit that supports BERT testing

After configuring test settings on both units, start the tests

Far-End Unit in Manual Loopback Mode

If the far-end unit (another MX) is already in a manual loopback mode, do not send a loop up command since it is

not necessary

Once the correct control settings are configured, the user can start the test

The selected tests will run automatically. When all the tests are complete the test will stop automatically. If the Throughput test

suite needs to be stopped before they are done, then simply press the

Stop

button, located in the actions drop-down menu. The

status of each selected test can be seen in the Results tab.

Far-End Unit Controlled with Loop Up/Down Commands

If the far-end unit is not manually looped back, then it must first receive a loop up command from the control unit

before the Throughput test suite can be started

To loop up the far-end unit with the manual mode loop up/down commands, configure the control settings mode to

manual

Enter the MAC and/or IP address of the far-end unit

Send the loop up command by pressing

Loop Up

Once the far-end unit has been looped back, start the test by pressing the

Start

button. When the all of the selected test are

completed, the Throughput test suite will stop automatically. Once all tests have been completed and there is no need to test

again, go back to the Control tab, and press the

Loop Down

button. This will send a loop down command to the far-end unit to

remove the loopback that is in place.

Go back to top

Go back to TOC

15.5.2 Throughput Results

15.5.2.1 Viewing Throughput (Multiple Streams) Test Results

When the test is first started, the screen automatically changes to the Global/Aggregate results screen.

15.5.2.2 Global/Aggregate Results

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды