VeEX VePAL TX300M Скачать руководство пользователя страница 304

Страница: 304 / 421

Test:

Select the test layer to perform the test.

Options are Layer 2, Layer 3, and Layer 4.

Frame Type:

Select the Ethernet frame type for Layer 2, Layer 3 or Layer 4.

802.3 Raw (IEEE 802.3 frame without LLC) - Not available when Layer 3 is selected

802.3 LLC (IEEE 802.3 frame with LLC header)

802.3 SNAP (IEEE 802.3 frame with SNAP header)

Ethernet II (DIX) (named after DEC, Intel, and Xerox, this is the most common frame type today)

MAC/IP:

Tap the MAC and IP blocks on the Frame image to access the setup menus.

Set the Source and Destination MAC address for Layer 2.

Set the Source and Destination MAC and IP addresses for Layer 3.

VLAN:

Off, 1 tag, 2 tags, 3 tags.

The user is able to configure up to 3 VLAN tags (VLAN stacking for Q-in-Q applications).

Note:

VLAN stacking is an option.

MPLS:

Off, 1 tag, 2 tags, 3 tags.

The user is able to configure up to 3 MPLS tags.

Note:

MPLS tag configuration is only available when the MPLS option is purchased.

MAC, VLAN, MPLS, IP, and Test Pattern Configurations:

Tap on the Frame image displayed on the screen to configure the MAC addresses, IP addresses, VLAN tag(s), MPLS

tag(s), and test pattern. This brings up the configuration screens for all the header fields.

Note:

For more information on header configuration please see

15.2.1.1 Header Settings

in the BERT section.

MAC Header Tab:

MAC Source:

Use the default source address of the test set or configure a new or different address. See MAC

address editing screen shot below.

MAC Destination

: Configure the destination MAC address of the far-end partner test set. See MAC address editing

screen shot below.

Ethernet Type:

For Layer 3 testing, the user can also configure the Ethertype:

0800-IP (Internet Protocol Version 4, IPv4)

0600-Xerox

0801-X.75 (X.75 Internet)

0805-X.25 (X.25 Level 3)

0806-ARP (Address Resolution Protocol [ARP])

8035-RARP (Reverse Address Resolution Protocol [RARP])

8137-IPX (Novell IPX)

814C-SNMP

8847-MPLS unicast

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды