VeEX VePAL TX300M Скачать руководство пользователя страница 285

Страница: 285 / 421

Options are Layer 1 Unframed, Layer 1 Framed, Layer 2, Layer 3, and Layer 4

Frame Type:

Select the Ethernet frame type for Layer 2 or Layer 3

802.3 Raw (IEEE 802.3 frame without LLC) - Not available when Layer 3 is selected

802.3 LLC (IEEE 802.3 frame with LLC header)

802.3 SNAP (IEEE 802.3 frame with SNAP header)

Ethernet II (DIX) (named after DEC, Intel, and Xerox, this is the most common frame type today)

MAC/IP:

Tap the MAC and IP blocks on the Frame image to access the setup menus

Set the Source and Destination MAC address for Layer 2

Set the Source and Destination MAC and IP addresses for Layer 3 and Layer 4

VLAN:

Off, 1 tag, 2 tags, 3 tags

The user is able to configure up to 3 VLAN tags (VLAN stacking, for Q-in-Q applications)

Note:

VLAN stacking is an option

MPLS:

Off, 1 tag, 2 tags, 3 tags

The user is able to configure up to 3 MPLS tags

Note:

MPLS tag configuration is only available when the MPLS option is purchased

The most common Ethernet Frame format, Type II

Go back to top

Go back to TOC

MAC, VLAN, MPLS, IP, and Test Pattern Configurations:

To configure the MAC addresses, IP addresses, VLAN tag(s), MPLS tag(s), and test pattern, tap on the frame image displayed

on the screen. This brings up the configuration screens for all the header fields.

MAC Header Tab:

MAC Source:

Use the default source address of the test set or configure a new or different address.

MAC Destination

: Configure the destination MAC address of the far-end partner test set or use the ARP or ARP

GW keys to determine the MAC address of the destination IP address (ARP) or the Gateway (ARP GW). Note that

a valid IP connection needs to be up to use these functions. Refer to

9.1 IP

in the

V300 Common Functions

manual

for details on IP connection.

Ethernet Type:

For Layer 3 testing, the user can also configure the Ethertype:

0800-IP (Internet Protocol Version 4, IPv4)

0600-Xerox

0801-X.75 (X.75 Internet)

0805-X.25 (X.25 Level 3)

0806-ARP (Address Resolution Protocol [ARP])

8035-RARP (Reverse Address Resolution Protocol [RARP])

8137-IPX (Novell IPX)

814C-SNMP

8847-MPLS unicast

8848-MPLS multicast

86DD (Internet Protocol, Version 6 [IPv6]) - Future Release

BERT Setup - MAC address settings (Layer 3)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды