VeEX VePAL TX300M Скачать руководство пользователя страница 323

Страница: 323 / 421

15.4 V-SAM

General
CIR Test Configuration
Header Settings
Service Attributes - Bandwidth Profile
Service Acceptance Parameters
MX Discover / Control Settings

Results

Configuration Test
Performance Test
Event Log

Overview

V-SAM (VeEX Service Activation Methodology) is an automated Ethernet service activation test feature conforming to the ITU-T

Y.1564 standard, created to address and solve the deficiencies of RFC 2544:

• RFC 2544 was limited to test at the maximum throughput line rate for a single service. SAM is able to run multiple

services on a single 10/100/1000 or 10G Ethernet line at a bandwidth ranging from 0 to the line rate, allowing for

more realistic stream testing

• The Frame Delay Variation, also known as (packet) jitter was not included in RFC 2544. Jitter is a critical

parameter for real time voice and video services. It is now part of the SAM test suite.

• RFC 2544 validates the service parameters like frame loss, throughput and latency, one after the other, while

SAM allows testing all the service critical parameters simultaneously. This results in significant time saving

compared to RFC 2544.

Comparison of RFC 2544 and Y.1564

Test Methodology

The purpose of the SAM test suite is to verify that the service is compliant to its Bandwidth Profile and Service Acceptance

Criteria. The test is broken down into two phases:

Phase 1: Service Configuration test

: The services running on the same line are tested one by one to verify the correct

service profile provisioning.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды