VeEX VePAL TX300M Скачать руководство пользователя страница 399

Страница: 399 / 421

Traffic Distribution - Traffic Type

Fibre Channel supports three classes of services, and a fourth which is a combination of classes 1 and 2.

Similar to ATM, different classes allow Fibre Channel to support a variety of communication needs.

Class 1:

Provides a circuit-emulation service for time-sensitive applications such as video teleconferencing.

Designed for dedicated, non-bursty links between supercomputers. Class 1 traffic is circuit-switched.

Class 2

: Provides guaranteed delivery for connectionless traffic.

Class 2 traffic is switched on each frame rather than on a connection. An acknowledgment from the destination provides

an end-to-end guarantee of delivery.

Class 3:

Offers a best-effort connectionless service.

Class 3 is similar to Class 2, except that no guarantee is given for delivery.

BERT - Traffic Type Distribution

Go back to top

Go back to TOC

Frame Size Distribution

Indicates the number and percentage of different frame sizes received during the test period.

BERT - Frame Size Distribution

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды