VeEX VePAL TX300M Скачать руководство пользователя страница 373

Страница: 373 / 421

15.8 Loopback Mode

The Loopback application in the main menu allows the user to establish a manual loopback on the test set. The loopback function is

used when an end-to-end test needs to be performed with one of the test partners in software loopback mode. The loopback function

will loopback the incoming traffic to the test set back into the network under test.

The type of traffic that the loopback function loops back will depend on the type of test layer configured (Layer 1, 2, 3, or 4). Additional

criteria can be set to allow only messages with specific criteria to be looped back. To specify loopback parameters, select the desired

parameter and choose

Enable

from the drop-down menu. Tap on the box and input a value or select one of the drop-down menu

choices:

Layer 1

: All incoming traffic to the Rx loopback interface will be sent out unaltered to the Tx loopback interface.

Layer 2, 3, & 4

: In a Layer 2 or 3 loopback all incoming test traffic will be looped back.

The loopback function will swap the MAC destination and MAC Source addresses (for Layer 2) or MAC and IP

destination and source addresses (for Layer 3).

All incoming frames with CRC errors will be dropped, similar to what an Ethernet switch does.

All broadcast and multicast frames will be dropped including any incoming unicast frames that have the MAC Source

address equal to the MAC Destination address.

Loopback Parameters

: The following parameters are available on Layer 2, 3 and 4. For more information on the

parameters, please see

15.2.1.1 BERT Header Settings

in the BERT section. It is possible to enable any of these

parameters to create a customer loopback filter. For example, enabling a filter with VLAN 64, Priority 7, will only loop

back traffic corresponding to these values.

VLAN ID

VLAN Priority

MAC Source

MAC Destination

IP Source Address (Layer 3 & 4 only)

IP Destination (Layer 3 & 4 only)

Precedence (Layer 3 & 4 only)

TOS Value (Layer 3 & 4 only)

UDP SPort (Layer 4 only)

UDP DPort (Layer 4 only)

Press

Start

to begin loopback.

indicates that loopback is in progress. The

Results

tab displays current test results. Please see

15.2.2 BERT Results

for information on the Results tabs.

Loopback Setup

Loopback In Progress

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды