VeEX VePAL TX300M Скачать руководство пользователя страница 49

Страница: 49 / 421

Network Type:

In the SONET mode, only optical interface options are available.

Test Rate:

Options are STS-1, OC-3, OC-12, OC-48, OC-192 (referring to 51M, 155M, 622M, 2.5G and 9.953G respectively).

Go back to top

Go back to TOC

Hierarchy > Through Mode

Tapping the Hierarchy box opens the Tx Hierarchy Setup screen.

Tx Hierarchy Setup - Through Mode

Through Mode:

Normal Mode:

Unit working as normal SONET mode.

Payload Through Mode:

Overhead overwrite Editing Thru mode allows for some intrusive error and alarm injection

through overhead manipulation.

Transparent Through Mode:

All the traffic goes through the unit untouched and the unit can monitor it. It is comparable

to Monitor Mode with a 10/90 splitter. In Transparent Mode, the unit regenerates the signal in amplitude. The clock is

recovered from the received signal.

Through modes are used to test network behavior under certain conditions, such as alarms and APS. To select Payload Through,

the payload has to be the same for the relevant ports.

Go back to top

Go back to TOC

Interface

Tapping the Tx Interface box opens the Tx Interface Setup screen. In this screen both electrical and optical options can be

selected.

Tx Interface Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды