VeEX VePAL TX300M Скачать руководство пользователя страница 340

Страница: 340 / 421

Alarm injection can be performed during test. The type of alarms and alarm injection are configured in the Alarm Injection tab.

Once the test is running, alarm injection can be performed by pressing the

Alarm Inject

button on the right side of the screen.

Note:

Alarm Injection is available only with 10GE Port Tests.

Alarm Type:

Local Fault, Remote Fault

Alarm Flow:

The alarm flow determines how the selected alarms will be injected. A specific Count or Continue

(continuous) can be selected.

Alarm Length:

1s, 10s, or 100s.

Throughput Alarm Injection Setup

Go back to top

Go back to TOC

15.5.1.7 Summary

The summary screen lists the source, destination and VLAN information of each stream. Tap on the appropriate box of each tab

to reconfigure the source, destination, or VLAN information if desired.

Throughput Test - Summary (MAC List)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды