VeEX VePAL TX300M Скачать руководство пользователя страница 146

Страница: 146 / 421

Go back to top

Go back to TOC

9.2.4 Optical Payload Unit (OPU) Analysis

Payload Structure Identifier (PSI)

Primary overhead field associated with the OPU

A 256-byte multiframe whose first byte is defined as the Payload Type (PT). The remaining 255 bytes are currently

reserved.

OPU PSI Type

The other fields in the OPU overhead are dependent on the mapping capabilities associated to the OPU. For an asynchronous

mapping (the client signal and OPU clock are different), Justification Control (JC) bytes are available to compensate for clock rate

differences. For a purely synchronous mapping (client source and OPU clock are the same), the JC bytes become reserved.

Further details on mapping are available in ITU G.709.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды