VeEX VePAL TX300M Скачать руководство пользователя страница 330

Страница: 330 / 421

AVAIL:

Minimum percentage of service availability allowed to still be compliant with the SLA. The service becomes

unavailable if more than 50% of the frames are errored or missing in a one second interval. Availability is only guaranteed

for traffic conforming to the CIR. Enter a percentage from 0-100. The user can also choose to

Disable

the AVAIL

threshold evaluation. AVAIL will be measured anyway but the value will not contribute toward passing or failing the

service.

Copying Services

Tap on the

Copy

button on the bottom of the

Header

Service Attributes

tabs to copy frame

parameters specific to that tab to other services. For example, pressing Copy on the Header tab will

only transfer header parameters to other services.

MX Discover and Control Settings

For instructions on how to loop up/down the TX300/e with another test set or device, please refer to

15.1.4 MX Discover and

Control

Go back to top

Go back to TOC

15.4.2 Results

Results - Config. Tests - Service 1

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды