VeEX VePAL TX300M Скачать руководство пользователя страница 54

Страница: 54 / 421

In E1 mode, the options are unframed, PCM31, PCM31C, PCM30, and PCM30C. Framing conforms to G.704 and G.706

recommendations and are briefly described below.

In E3 mode, the options are unframed, framed G.751.

Go back to top

Go back to TOC

Pattern

Tapping the Tx Pattern box opens the Tx Pattern Setup screen.

Tx Pattern Setup

Pattern:

Use the pattern drop-down box to select the test pattern which will be inserted into the transmitted signal. Pseudo

Random Bit Sequences (PRBS) defined by ITU-T 0.150 and 0.151 standards, fixed words and 24-bit or 32 bit user defined

patterns are available. Note, if the 32 bit user pattern entered is incorrect, the default pattern will be 0xFFFFFFFF.

Invert:

Inversion of polarity is also available.

Go back to top

Go back to TOC

6.4.2 Receiver Setup

Hierarchy

Tapping the Hierarchy setup box opens the Rx Hierarchy screen. The Hierarchy setup options for the Rx are the same as for the

Tx described previously.

Rx Hierarchy Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды