VeEX VePAL TX300M Скачать руководство пользователя страница 376

Страница: 376 / 421

VLAN Scan scans up to 4096 VLAN IDs for switch configuration and displays VLAN ID bandwidth rates, useful for identifying top

bandwidth users based on VLAN ID. Monitor mode monitors up to eight live traffic streams (in terminate mode) and filters them

based on VLAN ID configuration, providing key traffic metrics such as frame type, rates, and errors and alarms.

VLAN Scan

While traffic is being received, press

Scan

. The Results tab displays a list of detected VLAN IDs and the percentage of

traffic marked with those IDs. Check up to 8 streams to monitor.

VLAN ID

The VLAN Stack tab displays detected SP and CE VLAN tags (if stack VLAN tags are used).

VLAN Stack

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды