VeEX VePAL TX300M Скачать руководство пользователя страница 418

Страница: 418 / 421

20.0 Warranty and Software

Warranty Period:

The warranty period for hardware, software and firmware is three (3) years from the date of shipment to the

customer. The warranty period for battery pack, LCD, LCD touch panel, LCD protective cover, and accessories (including but not

limited to patch cords, AC adaptor, SFP, USB adaptors, carrying case, carrying pouch) is limited to one (1) year.

Hardware Coverage:

VeEX Inc. warrants hardware products against defects in materials and workmanship. During the warranty

period, VeEX will, at its sole discretion, either

Repair the products

Replace hardware which proves to be defective

provided that the products that the customer elects to replace is returned to VeEX Inc. by the customer along with proof of

purchase within thirty (30) days of the request by the customer, freight prepaid.

Software Coverage:

VeEX Inc. warrants software and firmware materials against defects in materials and workmanship. During

the warranty period, VeEX will, at its sole discretion, either

Repair the products

Replace the software and/or firmware which prove to be defective

provided that the products that the customer elects to replace is returned to VeEX Inc. by the customer along with proof of

purchase within thirty (30) days of the request by the customer, freight prepaid.

Additionally, during the warranty period, VeEX Inc. will provide, without charge to the customer, all fixes, patches and

enhancements to the purchased software, firmware and software options. VeEX Inc. does not warrant that all software or

firmware defects will be corrected. New enhancements attached to a software option require the option to be purchased (at the

time of order or the time of upgrade) in order to benefit from such enhancements.

Limitations:

The warranty is only for the benefit of the customer and not for the benefit of any subsequent purchaser or licensee

of any merchandise (hardware, software, firmware and/or accessories).

Revoking the warranty:

VeEX Inc. does not guarantee or warrant that the operation of the hardware, software or firmware will

be uninterrupted or error-free. The warranty will not apply in any of the following cases:

Improper or inadequate maintenance by the customer

Damage due to software installed by the customer on the unit without prior authorization (written) from VeEX Inc.

Unauthorized alteration or misuse

Damage occurred from operating the unit from outside of the environmental specifications for the product

Improper installation by the customer

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды