VeEX VePAL TX300M Скачать руководство пользователя страница 177

Страница: 177 / 421

Wait until the configuration message disappears, then press the

RESCAN

button at the bottom of the screen to start the Tributary

Scan monitoring function.

In the V-SCAN tab the test set will display the overall structure of the mixed payload tributaries in the form of a matrix, down to

the lowest SDH or SONET container (PDH or DSn structures within the containers will not be scanned). Tap on a member to

select it; the selection will turn blue. The LEDs will reflect the status of the currently selected tributary structure.

The V-SCAN Section

V-SCAN Header

Rate

: Displays the line rate of the interface under test

Ch #

: Displays the mapping type and channel number for the selected tributary

: Displays the Line/Section trace message

: Displays the trace identifier for the selected tributary

Note

: If the trace identifier for a particular tributary is set to 1-Byte, the label will be presented in its equivalent ASCII

representation and repeated 16 times (for example, the hex value 0x43 will be shown as “CCCCCCCCCCCCCCCC”.)

Tributary (High Order) Matrix

The Tributary Matrix shows the different combination of tributaries within the test signal. Touching any of the cells will

highlight it and make it the active tributary. LEDs on the right reflect the status of the selected tributary. Tap on the cell to

see the specific error/alarm affecting the tributary, represented by the blinking LED on the right.

White or blue cells indicate that everything is OK.

Red cells indicate problems or simply that particular tributaries are unequipped. Select alarmed tributaries to identify the

specific problems.

Intermittent red cells indicate a history of problems, bringing to attention defects or anomalies that happened in the past

but are no longer present. Selecting the intermittent cell will allow users to pinpoint the exact source of the problem. Use

the

Clear LED

button at the bottom of the screen to clear the history status.

V-SCAN Running

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды