VeEX VePAL TX300M Скачать руководство пользователя страница 41

Страница: 41 / 421

AU4 Mapping:

VC4-64C, VC4-16C, VC4-4C, VC4, VC3, and VC12 are available.

AU3 Mapping:

VC3,VC12, and TU11/VC11 are available.

Bulk:

Tap the check box to enable the setting. In bulk mode, the entire VT container is filled with a test pattern per ITU-T 0.181

recommendations.

Tributary:

Preset to DS1, E1, DS3, and E3 depending upon the options and mapping.

Channel Selection:

The Tx channel is selected by entering the STM-N, TUG-3, TUG-2, and TU-12 numbers for the channel.

Note:

TUG:

A Tributary Unit Group is the structure generated by combining several lower level tributaries into the next higher

level tributary

TU-12

: Each TU-12 frame consists of 36 bytes, structured as 4 columns of 9 bytes

At a frame rate of 8000Hz, these bytes provide a transport capacity of 2.304Mbps and accommodate the mapping

of a 2.048Mbps signal

63 x TU-12s may be multiplexed into a STM-1 VC-4

The tributary numbering used above is per ITU-T G.707 standard.

The high order paths are named using a C, B, A convention as follows:

C: The AUG-4 are numbered 1 to 4

B: The AUG-1 are numbered 1 to 4

A: The AU-3 are numbered 1 to 3

Thus the naming convention per SDH rate is as follows:

For STM-16: [C, B, A] convention is used

For STM-4: [B, A] convention is used

For STM-1 using AU-3 mapping: [A] convention is used

For STM-1 using AU-4 mapping: [0] convention is used

The low order paths are named using a K, L, M convention as follows:

K: TUG-3 are numbered 1 to 3

L: TUG-2 are numbered 1 to 7

M: TU-11, TU12, within the TUG-2 are numbered 1 to 4

Go back to top

Go back to TOC

Payload

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды