VeEX VePAL TX300M Скачать руководство пользователя страница 180

Страница: 180 / 421

The OTN Payload Structure Identifier (PSI) field displays a short decode of the Payload Mapping Type.

The Multiplex Section Synchronization Status Message (S1) field displays a short decode of the S1 Byte status for the line under

test.

0x00 Quality Unknown

0x02 ITU-T G.811 Recommendation

0x04 ITU-T G.812 SSU-A (Synchronization Supply Unit)

0x08 ITU-T G.812 SSU-B (Synchronization Supply Unit)

0x0B ITU-T G.813 Option I SEC (SDH Equipment Clock)

0x0F Do not use for synchronization

The High Order Path Signal Label (C2) field displays short decode indicating the type of payload carried in the selected group,

including the unequipped indication. A complete decoded message can be read in the Scanned Map Detail section. Some

examples are:

0x00 Unequipped

0x02 TUG Structure

0x03 Locked TU-n

0x04 Asynchronous Mapping of 34M or 45M

0x05 Experimental Mapping

0x12 Asynchronous Mapping of 140M

0x13 ATM Mapping

0x14 MAN DQDB Mapping

0x15 FDDI Mapping

0x16 Mapping of HDLC/PPP Framed Signal

0x18 Mapping of HDLC/LAPS Framed Signal

0x1A Mapping of 10G Ethernet Frames

0x1B GFP Mapping

0x1C Mapping of 10G Fibre Channel Frames

0x20 No Specify (Asynchronous Mapping of ODUk into VC-4-Xv)

0xFE Test Signal, O.181 Specific Mapping

0xFF VC-AIS

The Low Path or VT Signal Label (V5) field displays short decode for the type of payload carried in the selected container,

including the unequipped indication. Below is a list of the Signal Label (bits 5-7 of the V5 byte).

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды