VeEX VePAL TX300M Скачать руководство пользователя страница 385

Страница: 385 / 421

FC-3

defines common services that may be available across multiple ports in a node. This level has no standard now.

Services for multiple ports on one node

FC-4

defines the mapping between the lower levels of Fibre Channel, and the command sets that use Fibre Channel.

Upper Layer Protocol (ULP) mapping

Small Computer System Interface (SCSI)

Internet Protocol (IP)

High Performance Parallel Interface (HIPPI)

Asynchronous Transfer Mode - Adaption Layer 5 (ATM-AAL5)

Intelligent Peripheral Interface - 3 (IPI-3) (disk and tape)

Single Byte Command Code Sets (SBCCS)

Go back to top

Go back to TOC

16.2.2 Setup

FC-1 BERT - Test Frame Setup

Profile:

User Defined Profile or Default setting can be used for testing.

Test layer:

FC-1 or FC-2 only. Testing at other layers is not supported.

FC-1:

Information is transmitted using an adaptive code (8B/10B or 64/66B) depending on test rate and the encoding process

results in the generation of transmission characters.

The two types of Transmission Characters defined are data and special. Certain combinations of Transmission

Characters, referred to as Ordered Sets, are designated by this standard to have special meaning.

Ordered Sets are used to identify frame boundaries, transmit primitive function requests, and maintain proper link

transmission characteristics during periods of inactivity.

FC-1 Frame Structure

FC-2 BERT - Header Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды