VeEX VePAL TX300M Скачать руководство пользователя страница 148

Страница: 148 / 421

Go back to top

Go back to TOC

9.4 Trace Identifier (Trail Trace Identifier)

Tap the Trace Identifier icon to display the screen shown below. There are tabs for Tx and RX settings of the TTI.

Trace Identifier (Trail Trace Identifier)

Trail Trace Identifier

TTI similar to the J0 byte in SONET/SDH, is used to identify the signal from the source to the

destination within the network. The TTI contains the so called Access Point Identifiers (API) which

are used to specify the Source Access Point Identifier (SAPI) and Destination Access Point Identifier

(DAPI). The APIs contain information regarding the country of origin, network operator and

administrative details.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды