VeEX VePAL TX300M Скачать руководство пользователя страница 275

Страница: 275 / 421

A pop-up box will indicate when the clock is synchronized. Click OK. The unit is now ready to perform the

One Way

Delay

test.

Clock Synchronized

Go back to top

Go back to TOC

15.1.4 MX Discover and Control

Before proceeding with MX Discover or Control, be sure to assign an IP address to each test port. To assign an IP address, proceed

to the home menu and select the IP icon.

Note:

If using OAM Discover, it is unnecessary to assign an IP address to the local or remote unit.

MX Discover

MX Discover enables the TX300/e test set to discover other VeEX VePal test sets and devices with an assigned IP address on the

same subnet. To discover other devices using

MX Discover

Tap on the

MX Discover

button and then press

Discover

A list of discovered devices on the same IP subnet will appear. Select a unit to connect to from the list of devices.

Tap on

Close

to exit the window.

MX Discovery Tool

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды