VeEX VePAL TX300M Скачать руководство пользователя страница 356

Страница: 356 / 421

OAM Mode Active/Passive Actions

802.3ah OAM

Tap on the check box to start 802.3ah protocol testing. Transmission of OAM PDUs starts as soon as the box is checked.

OAM Mode

Select Active or Passive mode from the drop-down menu. Active and passive mode determines the type of actions the test set

will take. For more on acceptable Active/Passive mode combinations and actions, see section

802.3ah OAM Discovery

Vendor OUI and SPI

Organization Unique identifier and Vendor specific information (similar to MAC address fields).

Max PDU Length

Advertised Max OAM PDU size (64 to 1518). After Discovery, the lowest of the local and remote will be used.

PDU Rate

100 to 10000 ms between consecutive OAM PDUs.

Discovery Capability

Enables OAM enabled devices to exchange their OAM capabilities, configuration, and identity to link partners. Check on the

boxes to advertise selected capabilities during Discovery.

Go back to top

Go back to TOC

802.3ah OAM Discovery

Discovery is the first phase of the 802.3ah protocol. During Discovery, local and remote units exchange Information OAM PDUs

indicating capabilities and configuration information (mode, PDU size, loopback support, etc.). After successful negotiation the OAM

protocol is enabled on the link. If no OAM PDU is received after 5 seconds, Discovery is restarted. The device can be configured in

Active or Passive mode combinations.

OAM Mode - Acceptable Active/Passive

Combinations

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды