VeEX VePAL TX300M Скачать руководство пользователя страница 363

Страница: 363 / 421

Link Trace and Loopback Message Config. Parameters

Destination

MEP

: Sends LTM/LBM to the destination MEP as configured on Page 1.

MAC

: Sends LTM/LBM to a destination MAC address.

Priority:

802.1p priority in the LTM/LBM VLAN Tag.

Destination MAC:

Configure the destination MAC address used for the LTM/LBM. This field is only used if Destination is set to

MAC. If destination is set to MEP, this field is ignored

# Messages:

Enter the number of Loopback messages to be sent (LBM test only).

TTL:

Enter the Time to Live field in the LTM message. TTL will be decremented each time it crosses a hop (MIP) (LTM test

only).

Press

Start

to initiate testing.

Go back to top

Go back to TOC

Y.1731 Performance Management Functions

OAM - Service Level OAM (Page 3)

Loss (LMM/LMR) and Delay Measurement (DMM/DMR) Configuration Parameters

Destination

MEP

: Sends LMM/DMM to the destination MEP as configured on Page 1

MAC

: Sends LMM/DMM to a destination MAC address

Priority

- 802.1p priority in the LMM/DMM VLAN Tag

Destination MAC

- Configure the destination MAC address used for the LMM/DMM. This field is only used if Destination is set

to MAC. If destination is set to MEP, this field is ignored.

# Send

- Configure the number of LMM/DMM frames to send up to 50

Rate :

Configure the LMM/DMM frame interface rate (min: 100 ms; max: 10 seconds)

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды