VeEX VePAL TX300M Скачать руководство пользователя страница 270

Страница: 270 / 421

1 GE Copper Port

Auto Negotiation:

On or Off. Matches the test set's negotiation settings to those of the link partner.

Speed

(only when Auto Negotiation is Off): 10 Mbps, 100 Mbps, 1000 Mbps.

Duplex

(only when Auto Negotiation is Off): Half or Full.

Advertisement

(only when Auto Negotiation is On): Default-All or Custom. Custom options include 10/100/1000M/Half or

10/100/1000M/Full.

Flow Control:

TX On, RX On, Both On, or Off.

When flow control is On, the test set will respond to pause frames received by the link partner by adjusting the transmit

rate.

When flow control is Off, the test set ignores all incoming pause frames from the link partner and continues transmitting

at the configured transmit rate.

MDIX:

Off, On, or Auto. When MDIX is set to Auto, the test set detects the required cable connection type and configures the

port connection properly for interfacing the partner device, eliminating the need for crossover cables.

10GE Port Setup

Go back to top

Go back to TOC

10 GE Port

10GE Mode:

LAN or WAN

WIS Mode

(only available in WAN mode): SDH or SONET

Flow Control:

Enable chosen as default option

Clock Offset (ppm):

The frequency may be offset in parts per million

Status

Status tab

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды