VeEX VePAL TX300M Скачать руководство пользователя страница 382

Страница: 382 / 421

order to be displayed or be enabled.

Note:

The IP function is not supported in the V300 series.

Go back to top

Go back to TOC

16.1.3 Port Configuration

Fiber Channel - Port Setup

Fiber Profile:

Predefined Fiber Channel test profiles or Default setting

Speed:

Selectable test rates via drop-down menu:

1G (1.0625 Gbps)

2G (2.125 Gbps)

4G (4.25 Gbps)

8G (8.50 Gbps)

10G (10.52 Gbps)

Link Protocol:

Enables or Disables the PSP

Enabling the Primitive Sequence Protocol (PSP) allows link management

Disabling the Primitive Sequence Protocol (PSP) forces the port into an Active state with no link management

PSP is an Ordered Set transmitted repeatedly which is used to establish and maintain a link.

PSP also when this setting is enabled

When a Primitive Sequence is received and recognized, a corresponding Primitive Sequence or Idle is transmitted

in response. Recognition of a Primitive Sequence requires consecutive detection of 3 instances of the same

Ordered Set.

The Primitive Sequences supported by the standard are:

Offline (OLS)

Not Operational (NOS)

Link Reset (LR)

Link Reset Response (LRR)

Topology:

Point-to-Point (P-to-P) mode is supported.

Fibre Channel defines three topologies, namely, Point-to-Point, Arbitrated Loop, and Fabric however Point-to-Point

topology is the simplest one.

In Point-to-Point mode, only two ports are used, connected by a fiber optic link. The transmitter of each port is connected

directly to the receiver of the opposite port. There is no ambiguity in addressing, and there is no question of availability.

Login:

Disable only. Port login will be a future option.

Fibre Channel defines several types of ports. First of all, any port on a node device, (e.g., a PC, is an N_Port as

compared with a port on a Fabric, which is an F_Port).

Ports that connect switches together are called E_Ports. They generally do not need to follow Fibre Channel rules and

protocols.

Link Management:

Enable or Disable

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды