background image

INTRODUCTION

GE Conversion Kits are designed for upgrading
existing Allis Chalmers®, Siemens/Allis®, and
Siemens®

 

low-voltage power circuit breakers, rather

than replacing the entire breaker. The Conversion
Kits include MicroVersaTrip Plus™ or MicroVersaTrip
PM™ Trip Units, the latest technological advance in
GE trip systems.
MicroVersaTrip Plus and MicroVersaTrip PM Conver-
sion Kits are designed and tested to conform to ANSI
Standard C37.59, allowing the retrofitter to properly
install the kit and acceptance test the breaker.
This publication covers installation of
MicroVersaTrip Plus and MicroVersaTrip PM Con-
version Kits on Allis Chalmers®, Siemens/Allis®, and
Siemens® LA-800 and LA-1600 gold low-voltage
power circuit breakers. Each Conversion Kit contains
all the components needed to convert from the
existing trip system.

g

MicroVersaTrip Plus™ and

MicroVersaTrip PM™ Conversion Kits

for Allis Chalmers

®

, Siemens/Allis

®

, and

Siemens

®

 LA-800[F], and LA-1600[F] Gold

Low-Voltage Power Circuit Breakers

                                                                 

DEH–40009A  Installation Instructions

Содержание MicroVersaTrip Plus





















Отзывы: