VeEX VePAL TX300M Скачать руководство пользователя страница 337

Страница: 337 / 421

Multiple Streams

All streams are configured for the same test layer - if Layer 2 is selected, all streams will be Layer

2 traffic.

Go back to top

Go back to TOC

15.5.1.2 MX Discover and Control Settings

For instructions on how to loop up/down the TX300/e with another test set or device, please refer to

15.1.4 MX Discover and

Control

Go back to top

Go back to TOC

15.5.1.3 Per Stream Configurations

MAC Setup

MAC configuration in the Throughput section features MAC flooding for buffering verification and performance testing of Ethernet

switches.

Source (SRC) and Destination (Dest) flooding:

Enable or Disable.

Flood Range:

Specifies the number of MAC source and/or destination addresses. Enter a number from 0-4095. The

source and/or destination MAC addresses will be incremented by 1 until it reaches the number of times entered in the

flood range.

Note:

For information on header configuration please see

15.2.1.1 BERT Header Settings

in the BERT section.

Throughput Setup - Header Settings per Stream

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды