Toshiba e-studio 2555c, Руководство по обслуживанию

Страница: 442 / 1558

e-STUDIO2555C/3055C/3555C/4555C/5055C © 2012-2013 TOSHIBA TEC CORPORATION All rights reserved
SETTING / ADJUSTMENT
6 - 16
[D] Primary scanning data writing start position at duplexing
Notes:
Make sure the first line of the grid pattern is printed out since the line is occasionally vanished.
[D-1] Adjustment for long-sized paper
(1) While pressing [0] and [5] simultaneously, turn the power ON.
→
(Adjustment Mode)
(2) Press [3]
→
[FAX]. (A grid pattern with 10 mm pitch is printed out. Use A3/LD from the 2nd
drawer.)
(3) Check the grid pattern on the test print and measure the distance D from the left edge of the
paper to the 6th line of the grid pattern.
(4) Check if the distance D is within 52±0.5 mm.
(5) If not, use the following procedure to change values and measure the distance D again.
<Procedure>
(Adjustment Mode)
→
(Key in the code [4019])
→
[START]
→
[0]
→
[START]
→
(Key in a value (acceptable values: 0 to 255))
→
[OK] or [INTERRUPT] (Stored in memory)
→
“100% A” is displayed.
→
Press [3]
→
[FAX]
→
(A grid pattern is printed out.)
* The larger the adjustment value is, the longer the distance D becomes (approx. 0.04 mm/
step).
[D-2] Adjustment for short-sized paper
(1) While pressing [0] and [5] simultaneously, turn the power ON.
→
(Adjustment Mode)
(2) Press [3]
→
[FAX]. (A grid pattern with 10 mm pitch is printed out. Use A4/LT from the 1st
drawer.)
(3) Check the grid pattern on the test print and measure the distance D from the left edge of the
paper to the 6th line of the grid pattern.
(4) Check if the distance D is within 52±0.5 mm.
(5) If not, use the following procedure to change values and measure the distance D again.
<Procedure>
(Adjustment Mode)
→
(Key in the code [4019])
→
[START]
→
[1]
→
[START]
→
(Key in a value (acceptable values: 0 to 255))
→
[OK] or [INTERRUPT] (Stored in memory)
→
“100% A” is displayed
→
Press [3]
→
[FAX]
→
(A grid pattern is printed out.)
* The larger the adjustment value is, the longer the distance D becomes (approx. 0.04 mm/
step).
[D-3] Adjustment for medium-sized paper (Length: 220 mm to 329 mm)
1. While pressing [0] and [5] simultaneously, turn the power ON.
→
(Adjustment Mode)
2. Press [3]
→
[FAX]. (A grid pattern with 10 mm pitch is printed out. Use A4-R/LT-R from the 1st
drawer.)
3. Check the grid pattern on the test print and measure the distance D from the left edge of the
paper to the 6th line of the grid pattern.
4. Check if the distance D is within 52±0.5 mm.
5. If not, use the following procedure to change values and measure the distance D again.
<Procedure>
(Adjustment Mode)
→
(Key in the code [4019])
→
[START]
→
[2]
→
[START]
→
(Key in a value (acceptable values: 0 to 255))
→
[OK] or [INTERRUPT] (Stored in memory)
→
“100% A” is displayed
→
Press [3]
→
[FAX]
→
(A grid pattern is printed out.)
* The larger the adjustment value is, the longer the distance D becomes (approx. 0.04 mm/
step).