manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 70 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 70

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

66 

  

4.4.2.

 

SETUP – ACAL: AUTO CALIBRATION 

Used to set up and operate the internal valve options if installed. Section 6  provides 
details. 

4.4.3.

 

SETUP – DAS: DATA ACQUISITION 

Used to set up the data acquisition system and record data. 

4.4.4.

 

SETUP – RANGE: ANALOG OUTPUT REPORTING RANGE 

CONFIGURATION 

4.4.4.1.

 

Available  Analog Output Signals 

The analyzer has three active analog output signals, accessible through a connector on the 
rear panel. 

 

 

ANALOG OUT 

        A1         A2         A3         A4 

    +     -     +     -     +     -     +     -

 

H

2

S/SO

2

 

concentration outputs

 

HIGH range when 

DUAL mode is selected

 

Not Used

 

Test Channel

 

LOW range when 

DUAL mode is selected

 

 

Figure 4-3. Analog Output Connectors  Defined 

 

All three outputs can be configured either at the factory or by the user for full scale 
outputs of 0.1 VDC, 1VDC, 5VDC or 10VDC.  Additionally 

A1

 and 

A2

 may be equipped 

with optional 0-20 mADC current loop drivers and configured for any current output 
within that range (e.g. 0-20, 2-20, 4-20, etc.). The user may also adjust the signal level 
and scaling of the actual output voltage or current to match the input requirements of the 
recorder or data logger (See Sections 4.6.3.3 and 4.6.3.5). 

In its basic configuration, the 

A1

  and 

A2

  channels of the T101  output a signal that is 

proportional to the H

2

S concentration of the sample gas.  Several operating modes are 

available which allow them to be slaved together (

SNGL

  Mode, see Section 4.4.4.4 or 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов