manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 143 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 143

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

139 

4.8.2.7.

 

RS-232 Report Function 

The  T101  DAS  can automatically report data to the communications ports, where they 
can be captured with a terminal emulation  program or simply  viewed by the user.  

To enable automatic COM port reporting, follow the instruction shown in Section 
4.11.2.2 then press

: 

 

 

 

 

 
 

Edit Data Channel Menu 

From the 

DATA ACQUISITION

 menu 

 

 

 

SETUP X.X     

  

0)

 

CONC:     ATIMER,     2,       4032, R

 

 
 PREV  NEXT            INS    DEL

   EDIT    

 PRNT 

 

  EXIT

 

Exits to the main 

Data Acquisition 

menu 

 

 

 

SETUP X.X      

NAME:CONC

 

 
    <SET  

  SET> 

 EDIT

 

   PRINT 

 

EXIT

 

 

 

 

SETUP X.X      

RS-232 REPORT: OFF

 

 
    <SET    SET>

  EDIT 

   PRINT 

 

EXIT

 

ENTR

 accepts the new 

setting and returns to the 

previous menu. 

EXIT

 ignores the new setting 

and returns to the previous 

menu. 

SETUP X.X        

RS-232 REPORT: OFF

 

  

 OFF   

    

 

 

 

    ENTR    EXIT

 

 
 

Toggle  to turn 

reporting ON or OFF 

Press 

SET> 

 key until… 

 

 

4.8.2.8.

 

Compact Report 

When enabled, this option avoids unnecessary line breaks on all RS-232 reports. Instead 
of reporting each parameter in one channel on a separate line, up to five parameters are 
reported in one line,  instead. 

 

4.8.2.9.

 

Starting Date 

This option allows specifying a starting date for any given channel in case the user wants 
to  start data acquisition only after a certain time and date. If the 

Starting Date 

is in the 

past, the DAS ignores this setting. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов