manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 43 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 43

Teledyne ML – T101 Operation Manual 

Getting Started 

 

39 

3.3.5.

 

CONNECTING THE COMMUNICATIONS PORTS 

3.3.5.1.

 

Connecting the Serial Ports 

To utilize either of the analyzer’s two serial interfaces, refer to Sections 4.7 and 5 of this 
manual for instructions on configuration and usage.  For RS-485 communication, contact 
the factory. 

3.3.5.2.

 

Connecting  to a LAN or the Internet  

For network or Internet communication with the analyzer, connect an Ethernet cable from 
the analyzer’s rear panel Ethernet interface connector to an Ethernet port. (DHCP setup is 
the default, Section 4.7.6.1; manual setup for static IP address is recommended: see 
Section 4.7.6.2).

 

3.3.5.3.

 

Connecting to a Personal Computer (USB Option) 

For direct communication between the analyzer and a personal computer (PC), connect a 
USB cable between the analyzer and desktop or laptop USB ports. (If this option is 
installed, the COM2 port can only be used for RS232 multidrop communication).  See 
Section 4.7.7 for setup instructions. 

3.3.5.4.

 

Connecting to a Multidrop Network (Option) 

If your unit has the  Teledyne  ML  RS-232  Multidrop  Option  card  installed, see  Section 
4.7.8 for setup instructions. 

 

3.4.

 

PNEUMATIC CONNECTIONS 

 

CAUTION! 

Do not operate this instrument until you’ve removed dust plugs from SAMPLE and 
EXHAUST  ports  on the rear panel. (Plugs  were inserted into the rear panel pneumatic 
fittings  to prevent dust  from getting into the analyzer. It is recommended that these 
dust plugs be stored for future use such as shipping or storage.

 

 

Sample and calibration gases should only come into contact with PTFE (Teflon) or glass 
materials. They should  not come in contact with FEP or stainless steel materials. 

Figure  3-11  and  Figure  3-12  show the most common configurations for gas supply and 
exhaust lines to the Model T101 Analyzer.  Figure 3-14 shows  the connections for units 
with valve options  installed. 

Please refer to Figure 3-4 for pneumatic connections at the rear panel and Table 3-2 for 
their descriptions. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов