manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 78 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 78

Operating Instructions 

Teledyne  ML  – T101 Operation Manual 

74 

  

4.4.5.

 

SETUP – PASS: PASSWORD PROTECTION 

The  menu system  provides password protection of the calibration and setup functions to 
prevent unauthorized adjustments.  When the passwords have been enabled in the 

PASS 

menu item, the system will prompt the user for a password anytime a password-protected 
function  (e.g., SETUP) is selected.  This allows normal operation of the instrument, but 
requires the password (101) to access to the menus under SETUP. When PASSWORD is 
disabled (SETUP>OFF), any operator can enter the Primary Setup (SETUP)  and 
Secondary Setup (SETUP>MORE) menus. Whether PASSWORD is enabled or disabled, 
a password (default 818) is required to enter the VARS or DIAG menus in the 
SETUP>MORE menu. 

Table 4-6.  Password Levels 

PASSWORD 

LEVEL 

MENU ACCESS ALLOWED 

Null (000) 

Operation 

All  functions of the main menu (top level, or 

Primary,  menu) 

101 

Configuration/Maintenance  Access to Primary  and Secondary SETUP 

Menus when PASSWORD is enabled 

818 

Configuration/Maintenance  Access to Secondary SETUP Submenus VARS 

and DIAG whether PASSWORD is enabled or 

disabled. 

 

To enable or disable passwords, press: 

SETUP X.X       

 PRIMARY SETUP MENU

 CFG DAS RNGE

PASS

CLK MORE

EXIT

SAMPLE

              

RANGE=xxx.x PPX      [GAS]= xxxx

<TST TST> CAL

  

SETUP

SYSTEM        

PASSWORD ENABLE: OFF

 

OFF

ENTR EXIT

SETUP X.X        

PASSWORD ENABLE: ON

 

ON

ENTR EXIT

Toggle OFF to ON 

to enable, and ON 

to OFF to disable 

password feature

EXIT discards the new 

setting

ENTR accepts the new 

setting

SETUP X.X       

 PRIMARY SETUP MENU

 CFG DAS RNGE PASS CLK MORE

EXIT

SAMPLE

             

RANGE=xxx.x PPX          [GAS]= xxxx

<TST TST> CAL

  

SETUP

Press ENTR to 

accept new 

password, then 

EXIT the 

PRIMARY SETUP 

MENU so that 

selecting SETUP 

now prompts for 

the password.

SAMPLE             ENTER PASSWORD:0

0

  0

  0

ENTR

EXIT

Toggle to change 

password

 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов