manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 54 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 54

Getting Started 

Teledyne  ML  – T101 Operation Manual 

50 

  

The state of the IZS valves can also be controlled: 

•

 

Manually  from  the analyzer’s front panel by using  the SIGNAL I/O 

controls located under  the DIAG  Menu (Section 4.6.1), 

•

 

By  activating the instrument’s  AutoCal  feature (Section 6.9), 

•

 

Remotely  by using the external  digital  control inputs (Section 5.1.1.2  and 

Section 6.7.1), or 

•

 

Remotely  through  the RS-232/485  serial I/O ports (see Appendix A-6 for 

the appropriate  commands). 

 

3.5.

 

STARTUP, FUNCTIONAL CHECKS, AND INITIAL 

CALIBRATION 

If you are unfamiliar with the T101  theory of operation, we recommend that you read 
Section 10 before proceeding.  

For information on navigating the analyzer’s software menus, see the menu trees 
described in Appendix  A.1. 

3.5.1.

 

STARTUP 

After  the  electrical  and pneumatic connections are made, an initial functional check is in 
order. Turn on the instrument.  The pump and exhaust fan should start immediately.  The 
front panel display  screen  will briefly show a logo splash screen at the start of 
initialization. 

The analyzer should automatically switch to Sample Mode after completing the boot-up 
sequence and start monitoring H

2

S gas. However, there is an approximately one hour 

warm-up period before reliable gas measurements can be taken. During the warm-up 
period,  the front panel display  may show messages in the Parameters field.  

3.5.2.

 

WARM-UP 

Allow a 60-minute warm-up period before collecting  sample data. 

3.5.3.

 

WARNING MESSAGES 

Because internal temperatures and other conditions may be outside of specified limits 
during the analyzer’s warm-up period, the software will suppress most warning 
conditions  for 60 minutes after power up. 

If warning messages persist after 60 minutes, investigate their cause using the 
troubleshooting guidelines in Section  9. The following table includes a brief description 
of the various warning messages that may appear. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов