manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 181 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 181

Teledyne ML – T101 Operation Manual 

Calibration Procedures 

 

177 

6.7.

 

MANUAL CALIBRATION IN INDEPENDENT  OR AUTO 

REPORTING RANGE MODES 

If the analyzer is being operated in Ind  or  Auto  Range mode, then the High and Low 
ranges must be independently checked. 

When the analyzer is in either Independent or Auto Range modes the user must run a 
separate calibration procedure for each range.  After pressing the Cal,  CALZ  or  Cals 
buttons  the user is prompted for the range that is to be calibrated as seen in the CALZ 
example below: 

 

Continue Calibration as per 

Standard Procedure 

 SAMPLE           H2S STB = XXX.X PPB        

H2S 

=XXX.X  

 

 < TST  TST >  CAL

 

 

CALZ

   CALS

 

 

SETUP

 

ZERO CAL M

        H2S STB  XXX.XX PPB   

H2S 

=XXX.X 

  

 < TST  TST >  

ZERO

      

CONC

 

 

EXIT

 

Analyzer enters 

 ZERO CAL

 Mode 

See Table 5-1 for Z/S 

Valve States during 

this operating mode 

 SAMPLE  

RANGE TO CAL: LOW 

 

LOW  

 HIGH 

 

 

ENTR 

SETUP

 

 SAMPLE  

RANGE TO CAL: HIGH 

 

LOW   HIGH

 

 

 

ENTR

 

SETUP

 

Wait until 

H2S 

STB

 falls below

 

0.5 ppb. This may 

take several 

minutes. 

 

Once this selection is made, the calibration procedure continues as previously described 
in Sections 6.2 through 6.6.  The other range may be calibrated by starting over from the 
main 

SAMPLE

 display.

 

6.7.1.

 

CALIBRATION WITH REMOTE CONTACT CLOSURES 

Contact closures for controlling calibration and calibration checks are located on the rear 
panel  CONTROL IN connector. Instructions for setup and use of these contacts can be 
found in Section 5.1.2. 

When the appropriate contacts are closed for at least 5 seconds, the instrument switches 
into zero, low span or high span mode and the internal zero/span valves will be 
automatically switched to the appropriate configuration. The remote calibration contact 
closures  may  be  activated  in  any order. It is recommended that contact closures remain 
closed for at least 10 minutes to establish a reliable reading; the instrument will stay in the 
selected mode for as long as the contacts remain closed. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов