manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 213 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 213

Teledyne ML – T101 Operation Manual 

Instrument Maintenance

 

 

209 

8.3.6.

 

CHECKING FOR LIGHT LEAKS 

When re-assembled or operated improperly, the T101  can develop small leaks  around 
the PMT, which let stray light from the analyzer surrounding into the PMT housing. To 
find such light  leaks, follow  the procedures below. 

 

CAUTION 

This procedure can only be carried out with the analyzer running 

and its cover removed. This  procedure should only be carried out by 

qualified personnel. 

1.

 

Scroll  the TEST functions to PMT. 

2.

 

Supply  zero  gas to the analyzer. 

3.

 

With the instrument still running, carefully remove the analyzer cover. 

Take extra care not to touch any of the inside wiring  with the metal cover 

or your  body. Do  not drop  screws or  tools into  a running  analyzer! 

4.

 

Shine a powerful flashlight or portable incandescent light at the inlet and 

outlet fitting and at all of the joints of the sample  chamber  as well as 

around  the PMT housing.  The PMT value should  not respond  to the light, 

the PMT signal should remain  steady within its usual noise. 

5.

 

If there is a PMT response to the external light, symmetrically  tighten the 

sample  chamber mounting  screws or replace the 1/4” vacuum tubing 

with new, black PTFE tubing (this tubing will fade with time and become 

transparent). Often, light leaks are also caused by O-rings being  left out 

of the assembly. 

6.

 

Carefully  replace the analyzer cover. 

7.

 

If tubing or O-rings were changed, carry out a leak check (Section 

9.5.1). 

8.3.7.

 

CHANGING THE CRITICAL FLOW  ORIFICE 

A critical flow orifice, located on the exhaust manifold maintains the proper flow rate of 
gas through the T101 analyzer.  Refer to section 10.3.3.1 for a detailed description of its 
functionality and location. Despite the fact this device is protected by sintered stainless 
steel filters, it can, on occasion, clog, particularly if the instrument is operated without a 
sample filter or in an environment  with very fine, sub-micron particle-size dust.  

1.

 

Turn off power to the instrument and vacuum pump. 

2.

 

Locate the critical flow orifice on the pressure sensor assembly (called 

out in Figure  8-4). 

3.

 

Disconnect the pneumatic line. 

4.

 

Unscrew the NPT fitting. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов