manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 262 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 262

Principles Of Operation 

Teledyne ML - T101 Operation Manual

 

258

 

pressure differential combined with the action of the analyzer’s external pump draws the 
gas through the orifice. 

As the pressure on the downstream side of the orifice (the pump side) continues to drop, 
the speed that the gas flows though the orifice continues to rise. Once the ratio of 
upstream pressure to downstream pressure is greater than 2:1, the velocity of the gas 
through the orifice reaches the speed of sound. As long as that ratio stays at least 2:1 the 
gas flow rate is unaffected by any fluctuations, surges, or changes in downstream 
pressure because such variations only travel at the speed of sound themselves and are 
therefore cancelled out by the sonic shockwave at the downstream exit of the critical 
flow orifice. 

 

Figure 10-8.  Typical Flow Control Assembly  with Critical Flow Orifice 

 

The actual flow rate of gas through the orifice (volume of gas per unit of time), depends 
on the size and shape of the aperture in the orifice. The larger the hole the more gas 
molecules moving  at the speed of sound pass through the orifice. 

The result is that the flow rate of the gas is unaffected by degradations in pump 
efficiency due to age. 

The critical flow orifice used in the Model T101 is designed to provide a flow rate of 
600 cm3/min. 

 

10.3.4.

 

SAMPLE PARTICULATE FILTER 

To remove particles in the sample gas, the analyzer is equipped with a Teflon membrane 
filter of 47 mm diameter (also referred to as the sample filter) with a 1 µm pore size. The 
filter is accessible through the front panel, which folds down, and should be changed 
according to the suggested maintenance schedule in Table 9-1. 

 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов